xls116

High Speed Precision Rotary Sheet Cutter For Cardboard(roll to sheet) ,
Process
Freehand cut of heavy metal
The HF Contact type typically found in budget machines uses a high-frequency, high-voltage spark to ionise the air through the torch head and initiate an arc. These require the torch to be in contact with the job material when starting, and so are not suitable for applications involving CNC cutting.
The Pilot Arc type uses a two cycle approach to producing plasma, avoiding the need for initial contact. First, a high-voltage, low current circuit is used to initialize a very small high-intensity spark within the torch body, thereby generating a small pocket of plasma gas. This is referred to as the pilot arc. The pilot arc has a return electrical path built into the torch head. The pilot arc will maintain itself until it is brought into proximity of the workpiece where it ignites the main plasma cutting arc. Plasma arcs are extremely hot and are in the range of 15,000 degrees Celsius.
Plasma is an effective means of cutting thin and thick materials alike. Hand-held torches can usually cut up to 2 in (48 mm) thick steel plate, and stronger computer-controlled torches can pierce and cut steel up to 12 inches (300 mm) thick. Formerly, plasma cutters could only work on conductive materials; however, new technologies allow the plasma ignition arc to be enclosed within the nozzle, thus allowing the cutter to be used for non-conductive workpieces such as glass[citation needed] and plastics[citation needed] , electric guitar kit .
Since plasma cutters produce a very hot and very localized "cone" to cut with, they are extremely useful for cutting sheet metal in curved or angled shapes , cnc foam cutting .
Starting method , bits tools .
Plasma cutters use a number of methods to start the pilot arc, depending on the environment the unit is to be used in and its age. Older cutters use a high voltage, high frequency circuit to start the arc. This method has a number of disadvantages, including risk of electrocution, difficulty of repair, sparkgap maintenance, and the large amount of radio frequency emissions. Plasma cutters working near sensitive electronics, such as CNC hardware or computers, use the contact start method. The nozzle and electrode are in contact. The nozzle is the cathode, and the electrode is the anode. When the plasma gas begins to flow, the nozzle is blown forward. A third, less common method is capacitive discharge into the primary circuit via a Silicon Controlled Rectifier , cutting blades .
Inverter plasma cutters
Analog plasma cutters, typically requiring more than 2 kilowatts, use a heavy mains-frequency transformer. Inverter plasma cutters rectify the mains supply to DC, which is fed into a high-frequency transistor inverter between 10kHz to about 200kHz. Higher switching frequencies give greater effiencies in the transformer, allowing its size and weight to be reduced.
The transistors used were initially MOSFETs, but are now increasingly using IGBTs. With paralleled MOSFETs, if one of the transistors activates prematurely it can lead to a cascading failure of one quarter of the inverter. A later invention, IGBTs, are not as subject to this failure mode. IGBTs can be generally found in high current machines where it is not possible to parallel sufficient MOSFET transistors.
The switch mode topology is referred to as a dual transistor off-line forward converter. Although lighter and more powerful, some inverter plasma cutters, especially those without power factor correction, cannot be run from a generator (that means manufacturer of the inverter unit forbids doing so; it is only valid for small, light portable generators). However newer models have internal circuitry that allow units without power factor correction to run on light power generators.
Plasma gouging
Plasma gouging is a related process, typically performed on the same equipment as plasma cutting. Instead of cutting the material, plasma gouging uses a different torch configuration (torch nozzles and gas diffusers are usually different), and a longer torch-to-workpiece distance, to blow away metal. Plasma gouging can be used in a variety of applications, including removing a weld for rework. The additional sparks generated by the process requires the operator to wear a leather shield protecting their hand and forearm. Torch leads also can be protected by a leather sheath or heavy insulation.
CNC cutting methods
Plasma cutting with a CNC machine
Plasma cutting with tilting head with the HPR260
Plasma cutters have also been used in CNC (computer numerically controlled) machinery. Manufacturers build CNC cutting tables, some with the cutter built in to the table. The idea behind CNC tables is to allow a computer to control the torch head making clean sharp cuts. Modern CNC plasma equipment is capable of multi-axis cutting of thick material, allowing opportunities for complex welding seams on CNC welding equipment that is not possible otherwise. For thinner material cutting, plasma cutting is being progressively replaced by laser cutting, due mainly to the laser cutter's superior hole-cutting abilities.
A specialized use of CNC Plasma Cutters has been in the HVAC industry. Software will process information on ductwork and create flat patterns to be cut on the cutting table by the plasma torch. This technology has enormously increased productivity within the industry since its introduction in the early 1980s.
In recent years there has been even more development in the area of CNC Plasma Cutting Machinery. Traditionally the machines' cutting tables was horizontal but now due to further research and development Vertical CNC Plasma Cutting Machines are available. This advancement provides a machine with a small footprint, increased flexibility, optimum safety, faster operation, energy efficiency, ergonomic and more environmentally friendly.
New technology
High performance cut
In the past decade plasma torch manufacturers have engineered new models with a smaller nozzle and a thinner plasma arc. This allows near-laser quality on plasma cut edges. Several manufacturers have combined precision CNC control with these torches to allow fabricators to produce parts that require little or no finishing.
Costs
Plasma torches were once quite expensive. For this reason they were usually only found in professional welding shops and very well-stocked private garages and shops. However, modern plasma torches are becoming cheaper, and now are within the price range of many hobbyists. Older units may be very heavy, but still portable, while some newer ones with inverter technology weigh only a little, yet equal or exceed the capacities of older ones.
See also
Plasma arc welding
Water jet cutter
External links
HowStuffWorks on plasma cutting
Plasma Cutter Safe Work Method Statement
v  d  e
Metalworking
 
Tools
Cutting machines
Water jet cutter  Band saw  Cold saw  Laser  Miter saw  Plasma
Cutting tools
Broach  Burr  Chisel  Counterbore  Countersink  End mill  File  Guillotine shear  Hand scraper  Milling cutter  Nibbler  Reamer  Throatless shear  Tipped tool  Tool bit
Forming tools
Brake  Die  English Wheel  Flypress  Hydraulic press  Machine press  Punch press  Stamping press
Hand tools
Clamp  Combination square  Drift pin  File card  Hacksaw  Hammer  Hand scraper  Machinist square  Magnetic base  Needlegun scaler  Pipe and tube bender  Pliers  Punch  Saw piercing  Scriber  Tap and die  Tongs  Vise  Workbench  Wrench
Machine tooling
Angle plate  Chuck  Collet  Jig  Fixture  Indexing head  Lathe center  Machine taper  Magnetic base  Mandrel  Rotary table  Wiggler
Measuring instruments
Bore gauge  Caliper  Comparator  Dial indicator  Engineer's blue  Feeler  Center gauge and fishtail gauge  Gauge block  Gauge  Go-NoGo  Machinist square  Marking blue  Marking gauge  Marking out  Micrometer  Radius gauge  Scale  Sine bar  Spirit level  Straightedge  Surface plate  Tape measure  Thread pitch  Height gauge  Vernier scale  Wiggler
Smithing tools
Anvil  Forge  Fuller  Hardy hole  Hardy tools  Pritchel  Slack tub  Steam hammer  Swage block  Trip hammer
Casting  Fabrication  Forming  Jewellery  Machining  Metallurgy  Smithing  Tools & Terminology  Welding
Categories: Cutting machines | Metalworking cutting tools | Plasma processingHidden categories: Articles lacking sources from November 2008 | All articles lacking sources | All articles with unsourced statements | Articles with unsourced statements from May 2009